Springfield XD Forum banner

1 - 13 of 13 Posts

·
Registered
Joined
·
9,135 Posts
See question 34, I believe that is the one with the link tothe assembly directions provided by ajames.

General Questions and Answers:
Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If reading this with a / your gun nearby, please unload and verify the gun is unloaded now before proceeding any further with reading.
The questions and the answers listed here are taken from the questions and the answers and the comments of readers of this forum, not from the main dealer, manufacture, or a
Licensed gunsmith. Treat the comments listed here as a suggestion of what could be done.

If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS.

Never “play” with a handgun, loaded or not
Always unload the gun before handling.
Read the manufactures gun safety suggestions, and follow them.
Do take the time to attend a gun safety class(as).

Introduction to the XD Pistol: http://www.gunsandammomag.com/techside/xd_010305/
Another introduction to the XD, this time leaning towards the sub compact model, VERY informative site: http://www.thearmedcitizen.com/gunpages/xdcomp.htm

If your gun is near you now. UNLOAD IT, remove the ammuntion to a safe location in another room. Then verify the gun is unloaded. Then again verify the gun is unloaded AND that there is no ammunition in the same room as you are now with your gun/s.



1.)
Q: Can the magazine be left loaded for extended periods of time?
A: Yes, it will not hurt the magazine or the spring. Actually makes loading a full magazine easier.

2.)
Q: I can’t get the slide (aka dust cover) off?
A: Take the magazine out first.
B. Lock the slide back.
C. Flip the disassembly lever up,
D. Pull the trigger,
E. Slide the slide forward, it will come right off.

3.)
Q: Do XD’s rust.
A: Yes all metal can rust with improper care. Note, Improper care. Also, some XD’s may have a surface rust issue. Contact Springfield Armory about this.

4.)
Q: If my XD is rusting, will I have to pay SA to refinish it?
A: Depends on what type of rust. It is best to contact them for correct answer. Surface rust, generally they pay for basic refinish. Rust from damage, probably yes, you pay.
A: http://www.hs2000talk.com/viewtopic.php?t=20321&highlight=finish

5.)
Q: Can I put different sights in?
A: Yes. Some have a hard time, some easy. http://www.xd-hs2000.com/shopping


6.)
Q: Can I buy an XD and put in aftermarket barrels?
A: Yes. Pistolgear.com and AJAMES have some, as well as others here on the forum.



7.)
Q: Failure to feed / eject?
A: Try adjusting your magazine feed lips.
A: Dismantle and clean your magazine inside and lightly lube.
A: Are you “limp wristing”? Hold your wrist a little more stiff.
A: Is your thumb interfering with the slide action, many times this is the problem. Hold your thumb down just a little lower.
A: Sometimes the springs in the magazines need to be broken in. Leave the mags full until you get to the range. Give it a try
A: Defective design of the 40 S&W round. The short stubby round with a truncated cone bullet is just made to jam up against the chamber top, especially if the lip of the case catches on the edge of the chamber. It does not matter what gun, HK, Glock, SIG, S&W or CZ, the tying factor seems to be the round. My suggestion is try to use only rounds with rounded flat point, they seem to feed better. I know that does not do much in case of JHP usually but that is the nature of the beast

Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS.



8.)
Q: What is a good product to protect the XD?
A: Whatever works best for you.
A: Something safe for a polymer gun
A: Blue Wonder makes a product called Armadillo that works great.



9.)
Q: What is Armadillo?
A: A wax protectant for your metal parts. Heating the wax a little helps in the application of it, or the use of a wet warm application towel.

10.)
Q: Is brand XXXXXXX ammo any good?
A; Try it, find out.

11.)
Q: Brand XXXXXX ammo always jambs up my gun.
A: Use different ammo.
A: You might have to polish your feed ramp.

12.)
Q: What is the feed ramp?
A: With the gun disassembled, it is the part of the barrel where the shell casing enters. It is shinny and at an angle. The bullet nose and case slide up this to enter the barrel. Sometimes the ramp gets debris, scratched or even is just a little off angle for the type of round your are shooting.


13.)
Q: What is the best defense round?
A: The one that hits the target.

14.)
Q: Can I mount a holo sight on my gun?
A: Yes. There are sight mounts for the glocks that, with modification, Can fit the XD.
A: http://www.bb-enterprise.biz/

15.)
Q: Being a plastic gun, is it durable?
A: Yes. It is used be various militaries around the world.

16.)
Q: Where is the XD made?
A: Croatia. Europe. Used by their armed forces.



Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS.


17.)
Q: Can I put my buddies 40cal barrel in my 9mm frame.
A: NO.

18.)
Q: Can I buy other caliber barrels for my xd?
A: Yes. Check AJAMES or pistolgear.com. You can go with SMALLER barrels, not larger.

19.)
Q: Why can’t I rack the slide?
A: Are you holding the grip safety in?


20.)
Q: What should I do when the gun has a FTE?
A: Read your Manuel from the manufacture.





21.)
Q: Can I have the trigger reworked to a lighter pull?
A: Contact your local gunsmith
A: Ask on the forum.
A: Yes it can be done

22.)
Q: Should I wear a towel on my head to improve my shooting?
A: No. It just keeps the bugs off your head.

23.)
Q: Can I shoot my gun underwater?
A: Why would you want to? Some say yes, some say no. Ask Springfield for the Proper answer.

24.)
Q: Are there any accessories for the XD?
A: Yes. Every month more items are coming out. Again, check AJAMES and Pistolgear.com and others. Everything from holsters to lights and lasers. Barrels to refinishing.

25.)
Q: Can I replace my striker?
A: Yes, details online.

26.)
Q: What is stippling?
A: Customizing of the gun grip. It looks like somebody touches the grip a bunch of times with a hot soldering iron, creating little dimples all over the handle to improve grip.



Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS.

27.)
Q: What can I use to better the grip on my XD, on the cheap side?
A: Bicycle tire tube cut to length and slide it up on the handgrip.

28.)
Q: Do I need to oil my gun?
A: Yes. Lightly. Too much oil will attract dirt.
A: There are many different products out there to purchase and use. Dry lubricant’s work well.

29.)
Q: Do I need to oil my magazines?
A: Oil attracts dirt. Try a dry lubricant, or something such as CLP (Clean, Lubricate, Protect).


30.)
Q. Do I need to clean the XD after every use?
A: No. But it is good too do so. Some users have shot upwards of 4k to 5k rounds without cleaning. Some more, Some less. Some clean it every time. Some clean it every week, used or not.

31.)
Q: Will SA buy back my 10 round magazines?
A: Ask them. It depends on when you purchased the gun in relation to the ban expiring.

32.)
Q: I shoot low/high/left/right/ a little low and to the left. What am I doing wrong?
A: http://americanshooter.com/Features/features.html
A: http://www.backwoodshome.com/articles2/ayoob85.html

33.)
Q. What is WWB?
A. Winchester White Box ammo.

Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS







34.)
Q: My “chamber loaded” indicator is stuck in the UP position. What is wrong?
A: Is the gun loaded? Is a round in the chamber?
A: Parts 37,38, or 39... The spring keeps the indicator down until a round is chambered which lifts it up. I think what you will need to do is take down the entire slide dissemble.(you don't have to take out the extractor if you don't want to, this should not be part of your problem.) I would bet that you have some piece of "gunk" lodged between the slide frame and your indicator that is stuck in there. That will be easy enough to see after you remove the indicator, indicator spring, and indicator pin, and the entire slide assembly
http://www.xd-hs2000.com/disassembly/disassembly.html Click on slide disassembly.

35,)
Q. Are there any CAD drawings for the XD?
A. http://www.hs2000talk.com/viewtopic.php?t=20900&postdays=0&postorder=asc&start=30url
A. http://www.hs2000talk.com/viewtopic.php?t=21209&highlight=


36.)
Q. What is the size of a XD?
A. Slide width at widest point = 1.090"
Plastic frame width just below slide = 1.190"
grip just above magazine = 1.210"
Widest part of grip (includes the raised thumb "lump" area) = 1.264
Absolute widest point (includes protrusion from slide release) = 1.286"

If comparing to other guns, bear in mind Springfield measures the overall length the way I would (total length from end of barrel to whatever point extends farthest back, be it beavertail, slide, etc.). Some (Glock) measure the total slide length, but neglect to include the portion of the grip that extends even more behind that point.





Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS


37.)
Q. What is the size difference of a XD verses a Glock? Based on info from Glock and SA's sites, the following are published barrel lengths:

A.
Glock 19: 4.02"
XD9 Service: 4.05"
Glock 17: 4.49"
XD9 Tactical: 5.01"
Glock 34: 5.39"

A.




38.)
Q.) XD size compared to a sig?
A.) The XD service is nearly identical in size to the Sig 228/229
B.) Bianchi 19L holster shows the same size for the XD as the Sig 2340 & 2009

39.)
Q. Is the Bi-tone stainless steel?
A. YES Bi Tone is stainless. Bead blasted stainless and that's why it doesn't have the "bling". This it true. Remember, Stainless = Stain LESS. It CAN rust, but isn't as prone to rust. Also, there are different grades of stainless steel that will offer more or less resistance to rust.
B. No matter what you get, you still need to take care of it.





Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS


40.)
Q. Is the warranty transferable to a new owner?
A. According to their info pack that goes with the gun upon purchase. Paragraph one on the description of the "limited lifetime warranty". " Springfield, Inc. warrants to the initial retail purchaser that the products it wells will be free of defects in workmanship or material during his or her lifetime as long as he or she owns the product............" . Note that it says " ... initial retail purchaser...". However, later on it also states in the section titled " Disclaimer of Liability" (half way thru paragraph #2). " Springfield, Inc. will not be responsible for the results of careless handling, unauthorized repairs and adjustments, corrosion.........." .Note that it says S.A will not be responsible for ..........corrosion. And we know what they have been doing for corrosion.

41.)
Q. Ammo magazine descriptions- (as with everything else here, it is subjective)
A. *Standard capacity = a flush mag that does not extend past the end of the grip.

*High capacity = A mag that usually holds over 20 rounds and extends several inches from the grip.

*Clinton mag = a magazine that was designed to hold more then ten rounds, but had been altered to diminish the capacity to comply with federal legislation in effect from 1994 to 2004.

*Clip = A stripper clip that is designed to load various rifles such as a SKS.
42.)
Q. 9mm??????
A. 9mm Luger = 9mm Parabellum = 9x19mm = 9mm ammo. Just different name for the same thing.

43.)
Q. Who is a “Delija” and a “Captain Ray”?
A. Two guys having a contest too see who can: a.) open the other’s mind to the others thought’s, and b.) be meaner to each other.


Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS

44.)
Q. How loud is a gunshot?
A. http://www.freehearingtest.com/hia_gunfirenoise.shtml

45.)
Q. I can’t get the magazine to drop out without the mag button feeling like it’s going to break.

A. Take the base plates off the magazine. Then take a pot of boiling water.... drop the mag bases into the water for about 30-40 seconds. Dry the bases off and reinstall them on the magazine, load it up and give it a try. You will make the base plates more flexible by dehydrating them it wont cure anything but should help.


46.)
Q. What can I use to clean the polymer frame?
A. Quoted from “fsquared” who wrote to SA about this: “ I recently purchased a Springfield Armory XD40. This is the first firearm with polymer components that I have owned.

What solvents or cleaning materials do you recommend for the polymer frame of the firearm? Would WD-40 or like spray cleaners harm the frame and weaken it.

What would the effects be if I were to use a fast drying spray like Birchwood Casey's Gun Scrubber?

Or, what are your thoughts about using a "soap and water" approach with Simple Green solution?

Your expert advice is very much appreciated, thank you." “

Response from Springfield Armory (Terry Bowers):

"You can use the same solvents on the polymer frame as you would use on the steel slide. However, some solvents, such as WD-40 could possibly leave behind a slippery residue. Your best bet would be to stick with the soap and water or simple green approach. That polymer is very resistant to most solvents. Try to stay away from the very powerful solvents, as all you will need to clean the polymer will be good cleaning oil. I hope this helps a little. Please let me know if you have any more questions. Thanks."

Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS


47.)
Q. HELP, my rear sight has fallen out, should I use Locktight to secure it? And if I do, how can I be certain it is in the right place?
A. (Compliments of snak-eater1) Use a spring-loaded center punch to put some dimples in the bottom of the dovetail, this will raise up a little metal. Then use a brass punch to drift the rear sight back into position and to adjust windage. Once in place, you MIGHT want to locktite it into place, although I have never needed to do so after using the center punch method.









48.)
Q. How do I clean my gun?
A. Unload the gun, Unload the gun. Unload the gun. Unload the gun.

Items needed to clean the gun are: Bore cleaner, barrel brush, patches, lint free rags, newspaper / gun cleaning mat, air compressor, lubricant, gun metal protectant, tooth pick, toothbrush, cotton swabs. Make certain the gun is unloaded and no bullets or laded magazines are even in the same room as you and the gun.

Your gun general comes with at coarse brush used to go in the barrel and also for the outside of the gun. It's nylon (or some other type of plastic) that is a lot less hard than the gun barrel. I use Brass on mine (lubricated with bore cleaner) and I’ve never had a problem.

There are many "bore cleaners" out there to get rid of powder fouling in the barrel and around the moving parts of the gun, such as Shooter’s Choice, Hoppe’s#9, Blue Wonder's bore cleaner or Breakfree CLP.

Unload the gun.

Once you get the gun disassembled (read the manual), run the brush soaked in cleaner up and down the bore several times. Leave it, we'll get back to it later.

Next, clean the slide with the cleaner you just used to clean the bore. Soak a patch with it and rub all the metal parts, leaving them wet. You want to clean the top, bottom, and sides, of the slide. Every part you can and even some you cant see. Use the cotton swabs and toothbrush, toothpicks, patches for this. Pay particular attention to the "feed ramp", this is a part that must be clean and scratch free, as the bullet tips must slide along here to get into the barrel for firing.

Then clean the frame the same way. You won't need to worry as much about the plastic parts as they don't corrode like the metal parts will. Scrub all of the dirt out of the frame. Scrub down the metal parts and leave them wet. You really don't need to get the frame soaking in the bore cleaner.

Now back to the barrel. Run a patch soaked with solvent down the barrel. Next use a dry patch until the patch comes out clean. You may have to run a wet patch, dry patch, wet patch dry patch a few times, do this until they come out clean, The barrel is now cleaned, Put it aside as you wipe off the slide and frame.

If you have an air compressor, use it to dry off the gun after all the pieces are clean. If not, use a lint free rag.

Next, You will want to apply a lube to the moving parts of the gun, JUST A LITTLE. Notice I said lube, not oil. You can use oil, or you can use a product like Blue Wonder's DISORTEC XFR, DuPont Teflon, Gun Butter, something.

Wipe off any excess lube.
Make certain the gun is unloaded.

Reassemble; rack the slide a few times to work the lube into the moving parts.


Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS


49.)
Q. I am NEW to handguns, what are some basic rules I should / could know?
A. The following is a link to the NRA web site. Go here http://www.nrahq.org/education/guide.asp for some great information on safety for you and your family. Always treat the gun (handgun / long gun) as being LOADED. Sign up for gun safety classes ASAP. Sign up for gun Handling classes, how to aim, etc.
There are some people that have been shooting for years, that still sign up for classes from professionals as refreshers. It’s better to be knowledgeable, safe and alive, then stupid and dead.

50.)
Q. Once I get to be a good shot with my handgun, what can I do then for fun with it?
A. Well, here is a list of BAD things to use a gun for: bank robbery, car jacking, armed assault, terrorist, hi-jacker, armored car robber, candy stealer from kids.
A. Here is a list of what you can do once you are proficient with your handgun: http://idpa.com. Check it out. Or you can get into the old revolver western shoots held in some areas.

Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS

51.)
Q. How long will the recoil spring assembly last? Should I change it after a pre-determined amount of shots fired?
From a post by : kennyusmc1
Posted: Mon Oct 17, 2005 1:14 pm Post subject: oem guide rods spring

In a previous post, someone said SA was very strict about changing your recoil assy after 2000 rounds, here is a reply from SA after inquiry about replacement . If the recoil assembly has worn prematurely, and is causing a problem with the function of the pistol, it will be covered under warranty. We do not have an actual round count as to when the recoil assembly will need to be replaced. This would be determined by the caliber of the pistol, the type of load being put through it and so on. There are many variables involved. It is warranted for function from the factory, but not if it has just been worn out. I have heard of many of them lasting well beyond 10,000 rounds. If you would like us to take a look at your pistol for you, we would certainly be happy to. Those recoil assemblies are available from us. They are available for purchase and cost $14 apiece. The part number is XD5190. If you have any other questions, please let me know. Thank you. With Best Regards, Terry Bowers Regional Dealer Relations Springfield Armory Inc. 420 W. Main St. Geneseo, IL 61254 www.springfield-armory.com 1-800-680-6866 (ext. 8938) 1-800-617-6597 [email protected]
 

·
Registered
Joined
·
34 Posts
Discussion Starter #3
Alas, Ajames never details the disassembly of the magazine catch.

Another shortfall of the disassmbly guide is that it's just that - a disassembly guide. Some things, in particular the rear frame components - take a little finess to get back together. The guides great though.

The trick of the magazine catch is that the release button appears to need to be in position prior to the insertion of magazine catch and spring.

With the catch levered forward in it's normal position by the button there's no room to slip the spring in there afterwards. With the spring in position it takes an abhorrent amount of force and hold in place and manuever the catch into place.

The current plan is to improvise a small pin (paper clip once I find one) and use it to pin the catch and spring together, place them and then tap the magazine pin into place - pushing the paperclip out the other side...
 

·
Registered
Joined
·
34 Posts
Discussion Starter #5
Done and Done! Thanks for the tips and finding the video. Someone ought to sticky this or put the video up on the website!

Thanks again :D
 

·
Registered
Joined
·
1,013 Posts
Troupe said:
anyone have a new link havd a prob taking my catch assembly apart
Actually, there is a video available in ajames's forum.

It is a sticky there.

http://www.xdtalk.com/forums/showthread.php?t=7146

The video is VERY helpful if you take it completely apart instead of just one side at a time like the pg tutorial.

It worked in october. Don't know if it's still working now. If not, email ajames... he can repost it if the link on his website is down (I heard he was redesigning the website or something?)
 

·
Registered
Joined
·
19 Posts
for the record, case someone else runs into this; finally removed the catch assembly. For some reason the spring did come off of the pin even though I followed the directions and did not remove the pin only enough to get the mag release button out.

Anyways, I got the pin out of the assembly it was stuck. The spring was blocking the pin from allowing me to reinsert it to the other side. This caused my spring to bend, I un-bent it and it fits the pin again. I just don't see how it is humanly possible to get this assembly back in. Last straw is the gunsmith on Monday.







Any suggestions?
 

·
Registered
Joined
·
2,736 Posts
I found it was MUCH easier to reassmble the spring/catch/pin with the button fully out of the frame. Once I got the pin through one side of the catch and into the spring (I used a brass punch to hold eveything together while I was working on it) I put the button back in and finished the assembly as shown in the PistolGear video.
 
1 - 13 of 13 Posts
Top