Springfield XD Forum banner

1 - 11 of 11 Posts

·
Registered
Joined
·
133 Posts
Discussion Starter #1
Hi Guys,

Just purchased a Service Model XD .40 Cal (All Black) ... the bad news is that I have to wait a couple days as the shop was out of stock...

They are running a May Special of $407 for the Service (4") and $429 for the Tactical (5") models... not bad compared to what I've been seeing...

I'm looking forward to hitting the range and purchasing a light/laser combo for home protection ...

I have a feeling this is going to be addictive as I already have my eye on a 9mm Sub Compact and the 45 Gap Bi-Tone 5" model...

This site is full of useful posts...and is very helpful in selecting the right equipment...Thanks...

Take care,
TIM
 

·
Registered
Joined
·
513 Posts
Congrats. Watch out for those Pistol Gear guys, they have alot of stuff and great service. Give them a try for some add on's to your new piece.
 

·
Registered
Joined
·
133 Posts
Discussion Starter #5
Thanks for the words fellas...

I'm looking forward to all the fun...
 

·
Registered
Joined
·
9,135 Posts
Congratulations on your XD purchase!!! Fun and addictive. I just bought a red dot scope and ordered a scope mount yesterday for my XD.

Here are some general questons and suggestions that have been asked in the past by new / old /cranky members that you may find helpfull.

Again.......Enjoy!!!!!

General Questions and Answers:
Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If reading this with a / your gun nearby, please unload and verify the gun is unloaded now before proceeding any further with reading.
The questions and the answers listed here are taken from the questions and the answers and the comments of readers of this forum, not from the main dealer, manufactuer, or a
licensed gun smith. Treat the comments listed here as a suggestion of what could be done.

If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS.

Never “play” with a handgun, loaded or not
Always unload the gun before handling.
Read the manufactures gun safety suggestions, and follow them.
Do take the time to attend a gun safety class(es).

Introduction to the XD Pistol: http://www.gunsandammomag.com/techside/xd_010305/
Another introduction to the XD, this time leaning towards the sub compact model, VERY informative site: http://www.thearmedcitizen.com/gunpages/xdcomp.htm



1.)
Q: Can the magazine be left loaded for extended periods of time?
A: yes, it will not hurt the magazine or the spring. Actually makes loading a full magazine easier.

2.)
Q: I can’t get the slide (aka dust cover) off?
A: Take the magazine out first.
B. Lock the slide back.
C. Flip the disassembly lever up,
D. Pull the trigger,
E. Slide the slide forward, it will come right off.

3.)
Q: Do XD’s rust.
A: Yes all metal can rust with improper care. Note, Improper care. Also, some XD’s may have a surface rust issue. Contact Springfield Armory about this.

4.)
Q: If my XD is rusting, will I have to pay SA to refinish it?
A: Depends on what type of rust. It is best to contact them for correct answer. Surface rust, generally they pay for basic refinish. Rust from damage, probably yes, you pay.
A: http://www.hs2000talk.com/viewtopic.php?t=20321&highlight=finish

5.)
Q: Can I put different sights in?
A: Yes. Some have a hard time, some easy. http://www.xd-hs2000.com/shopping


6.)
Q: Can I buy an XD and put in aftermarket barrels?
A: Yes. Pistolgear.com and AJAMES have some, as well as others here on the forum.



7.)
Q: Failure to feed / eject?
A: Try adjusting your magazine feed lips.
A: Dismantle and clean your magazine inside and lightly lube.
A: Are you “limp wristing”? Hold your wrist a little more stiff.
A: Is your thumb interfering with the slide action, many times this is the problem. Hold your thumb down just a little lower.
A: Sometimes the springs in the magazines need to be broken in. Leave the mags full until you get to the range. Give it a try
A: defective design of the 40 S&W round. The short stubby round with a truncated cone bullet is just made to jam up against the chamber top, especially if the lip of the case catches on the edge of the chamber. It does not matter what gun, HK, Glock, SIG, S&W or CZ, the tying factor seems to be the round. My suggestion is try to use only rounds with rounded flat point, they seem to feed better. I know that does not do much in case of JHP usualy but that is the nature of the beast

Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS.



8.)
Q: What is a good product to protect the XD?
A: Whatever works best for you.
A: Something safe for a polymer gun
A: Blue Wonder makes a product called Armadillo that works great.



9.)
Q: What is Armadillo?
A: A wax protectant for your metal parts. Heating the wax a little helps in the application of it, or the use of a wet warm application towel.

10.)
Q: Is brand XXXXXXX ammo any good?
A; Try it, find out.

11.)
Q: Brand XXXXXX ammo always jambs up my gun.
A: Use different ammo.
A: You might have to polish your feed ramp.

12.)
Q: What is the feed ramp?
A: With the gun disassembled, it is the part of the barrel where the shell casing enters. It is shinny and at an angle. The bullet nose and case slide up this to enter the barrel. Sometimes the ramp gets debris, scratched or even is just a little off angle for the type of round your are shooting.


13.)
Q: What is the best defense round?
A: The one that hits the target.

14.)
Q: Can I mount a holo sight on my gun?
A: Yes. There are sight mounts for the glocks that, with modification, Can fit the XD.
A: http://www.bb-enterprise.biz/

15.)
Q: Being a plastic gun, is it durable?
A: Yes. It is used be various militaries around the world.

16.)
Q: Where is the XD made?
A: Croatia. Europe. Used by their armed forces.



Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS.


17.)
Q: Can I put my buddies 40cal barrel in my 9mm frame.
A: NO.

18.)
Q: Can I buy other caliber barrels for my xd?
A: Yes. Check AJAMES or pistolgear.com.

19.)
Q: Why can’t I rack the slide?
A: Are you holding the grip safety in?


20.)
Q: What should I do when the gun has a FTE?
A: Read your Manuel from the manufacture.





21.)
Q: Can I have the trigger reworked to a lighter pull?
A: Contact your local gunsmith
A: Ask on the forum.
A: Yes it can be done

22.)
Q: Should I wear a towel on my head to improve my shooting?
A: No.

23.)
Q: Can I shoot my gun underwater?
A: Why would you want to? Some say yes, some say no. Ask Springfield for the Proper answer.

24.)
Q: Are there any accessories for the XD?
A: Yes. Every month more items are coming out. Again, check AJAMES and Pistolgear.com and others. Everything from holsters to lights and lasers. Barrels to refinishing.

25.)
Q: Can I replace my striker?
A: Yes, details online.

26.)
Q: What is stippling?
A: Customizing of the gun grip. It looks like somebody touches the grip a bunch of times with a hot soldering iron, creating little dimples all over the handle to improve grip.



Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS.

27.)
Q: What can I use to better the grip on my XD, on the cheap side?
A: Bicycle tire tube cut to length and slide it up on the handgrip.

28.)
Q: Do I need to oil my gun?
A: Yes. Lightly. Too much oil will attract dirt.
A: There are many different products out there to purchase and use. Dry lubricant’s work well.

29.)
Q: Do I need to oil my magazines?
A: Oil attracts dirt. Try a dry lubricant if you must.


30.)
Q. Do I need to clean the XD after every use?
A: No. But it is good too do so. Some users have shot upwards of 4k to 5k rounds without cleaning. Some more, Some less. Some clean it every time. Some clean it every week, used or not.

31.)
Q: Will SA buy back my 10 round magazines?
A: Ask them. It depends on when you purchased the gun in relation to the ban expiring.

32.)
Q: I shoot low/high/left/right/ a little low and to the left. What am I doing wrong?
A: http://americanshooter.com/Features/features.html
A: http://www.backwoodshome.com/articles2/ayoob85.html

33.)
Q. What is WWB?
A. Winchester White Box ammo.

Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS







34.)
Q: My “chamber loaded” indicator is stuck in the UP position. What is wrong?
A: Is the gun loaded. Is a round in the chamber?
A: Parts 37,38, or 39... The spring keeps the indicator down unitl a round is chambered which lifts it up. I think what you will need to do is take down the entire slide dissembly..(you don't have to take out the extractor if you don't want to, this should not be part of your problem.) I would bet that you have some piece of "gunk" lodged between the slide frame and your indicator that is stuck in there.. that will be easy enough to see after you remove the indicator, indicator spring, and indicator pin, and the entire slide assembly
http://www.xd-hs2000.com/disassembly/disassembly.html Click on slide disassembly.

35,)
Q. Are there any CAD drawings for the XD?
A. http://www.hs2000talk.com/viewtopic.php?t=20900&postdays=0&postorder=asc&start=30url
A. http://www.hs2000talk.com/viewtopic.php?t=21209&highlight=


36.)
Q. What is the size of a XD?
A. Slide width at widest point = 1.090"
Plastic frame width just below slide = 1.190"
grip just above magazine = 1.210"
Widest part of grip (includes the raised thumb "lump" area) = 1.264
Absolute widest point (includes protrusion from slide release) = 1.286"

If comparing to other guns, bear in mind Springfield measures the overall length the way I would (total length from end of barrel to whatever point extends farthest back, be it beavertail, slide, etc.). Some (Glock) measure the total slide length, but neglect to include the portion of the grip that extends even more behind that point.





Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS


37.)
Q. What is the size difference of a XD verses a Glock?
A.




38.)
Q.) XD size compared to a sig?
A.) the XD service is nearly identical in size to the Sig 228/229
B.) Bianchi 19L holster shows the same size for the XD as the Sig 2340 & 2009

39.)
Q. Is the Bi-tone stainless steel?
A. YES Bi Tone is stainless. Bead blasted stainless and that's why it doesn't have the "bling".This it true. Remember, Stainless = Stain LESS. It CAN rust, but isn't as prone to rust. Also, there are different grades of stainless steel that will offer more or less resistance to rust.
B. No matter what you get, you still need to take care of it.





Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS


40.)
Q. Is the warrenty transferabile to a new owner?
A. According to their info pack that goes with the gun upon purchase. Paragraph one on the description of the "limited lifetime warrenty". " Springfield, Inc. warrents to the initial retail purchaser that the products it wells will be free of defects in workmanship or material during his or her lifetime as long as he or she owns the product............" . Note that it says " ... initial retail purchaser...". however, later on it also states in the section titled " Disclaimer of Liability" ( half way thru paragraph #2) . " Springfield, Inc. will not be responsible for the results of careless handeling, unauthorized repairs and adjustments, corrosion.........." .Note that it says S.A will not be responsible for ..........corrosion. And we know what they have been doing for corrosion.

41.)
Q. Ammo magazine descriptions- (as with everything else here, it is subjective)
A. *Standard capacity = a flush mag that does not extend past the end of the grip.

*High capacity = A mag that usually holds over 20 rounds and extends several inches from the grip.

*Clinton mag = a magazine that was designed to hold more then ten rounds, but had been altered to diminish the capacity to comply with federal legislation in effect from 1994 to 2004.

*Clip = A stripper clip that is designed to load various rifles such as a SKS.
42.)
Q. 9mm??????
A. 9mm Luger = 9mm Parabellum = 9x19mm = 9mm ammo. Just different name for the same thing.

43.)
Q. Who is a “Delija” and a “Captain Ray”?
A. Two guys having a contest too see who can be meaner to each other.


Author assumes no responsibility for actions taken by users of this Q & A section.
Use these SUGGESTIONS at YOUR OWN RISK!
If in doubt, consult your Manuel for your handgun.
If in doubt, consult a reputable firearms service center.
If in doubt, consult SPRINGFIELD ARMS

44.)
Q. How loud is a gun shot?
A. http://www.freehearingtest.com/hia_gunfirenoise.shtml
 

·
Registered
Joined
·
133 Posts
Discussion Starter #7
Information Overload :lol:

Thanks Tec ...

Good Stuff!
 

·
Registered
Joined
·
415 Posts
Tec,
Are you sick of noobie questions or what? :D
 

·
Registered
Joined
·
9,135 Posts
nogoa said:
Tec,
Are you sick of noobie questions or what? :D
a resounding NO I shout out.

No way, nuh uh.

I know that some of the other members (a few) have complained about newbs asking questions that "have been posted before".

Or telling the newb's to "check the search, did ya check the search, ya didnt check the search did ya?"

I don't really want to see any newbs scared off or afraid to ask questions, so I try to give them a "mostly one stop shop".

I am not an expert on guns, but I am pretty good at copying others words.
 

·
Registered
Joined
·
415 Posts
Sounds good to me, but we don't hear enough from (TASF)Overikill since he has been working.
 

·
Registered
Joined
·
3,263 Posts
buy the tactical and you will be sunk. I may as well say it now, Welcome to the addiction, now repeat after me.

"Hi my name is __________________ and I am a XDholic. I do not want to stop and you can't make me. Now load my mags and I might think about letting you shoot it."
 
1 - 11 of 11 Posts
Top