As some Springfield Armory pistols have a grip safeties they do not make a specific grip,
There is another solution that may work for you?
As you can see, the grip safety is still exposed.
Hogue grip # for XDm 10mm 4.5 inch
1 - 20 of 43 Posts
There is another solution that may work for you?
As you can see, the grip safety is still exposed.
Thanks. My screen name change I asked for happened!
I went into a gun shop who said if a rubber grip fits the 45 acp it has the same size frame as 10mm. Looking at the Hogue web site, this one should work. I’d like the finger swells on the front.
Sku: 17303 in FDE
![Air gun Trigger Gun barrel Gun accessory Recreation]()
![Font Thigh Waist Poster Human leg]()
Sent from my iPhone using Tapatalk
I went into a gun shop who said if a rubber grip fits the 45 acp it has the same size frame as 10mm. Looking at the Hogue web site, this one should work. I’d like the finger swells on the front.
Sku: 17303 in FDE
Sent from my iPhone using Tapatalk
Despite multiple emails from Hogue saying it would not fit, with a little trimming on the bottom- it fits. Model 17303 in desert tan is close enough to the factory fde.
I want to keep the top well below the safety so if it does slide upwards, it will not interfere with the safety.
As far as the bottom, as a friend of my son told me when we were hunting ducks at Sacramento National Wildlife Refuge , “there’s no points for pretty out here, Bill”. As my defensive weapon for grizzers here in Montana (bear spray doesn’t work if the wind is swirling or in your face), it’s between me, the beast and meeting Jesus long before I die of old age.
I hope this helps somebody else out.
![Air gun Trigger Gun barrel Gun accessory Metal]()
![Calipers Wood Gas Machine Auto part]()
Sent from my iPhone using Tapatalk
I want to keep the top well below the safety so if it does slide upwards, it will not interfere with the safety.
As far as the bottom, as a friend of my son told me when we were hunting ducks at Sacramento National Wildlife Refuge , “there’s no points for pretty out here, Bill”. As my defensive weapon for grizzers here in Montana (bear spray doesn’t work if the wind is swirling or in your face), it’s between me, the beast and meeting Jesus long before I die of old age.
I hope this helps somebody else out.
Sent from my iPhone using Tapatalk
I wonder if this Hogue grip could fit on my SA XDm 10mm with its thicker mag like a glock 40 10mm?
It may take some doing and need trimming but it looks like it may work?
When you cannot find what you are looking for maybe "Afro Engineering" will do just fine.
While all slip-ons add so much extra thick rubber, stick-ons are not always the answer either.
How about Bomeek sleeve Shotgun shockwave?
Hear me out: They are thin stretchable rubber, easy to trim if needed, do not slip once installed and cheap.
This is that same Rubber sleeve on my AR pistol grip.
A double stack 45/10mm is thick for my female hands but I am going to try this Rubber Sleeve, and not only on my SA XDm 10mm compact but on other firearms I own.
Ok, I got the two rubber slip-on today and installed them on my XDm Elite 10mm compact and my Sig P-365 xl
I need to get new razor blades before I cut them.
At least you know they can work and soon cut to match grip frame.
Attachments
I cut rubber to frame.
I do not see any way for the grip safety to be an issue?
I usually goto my range on Wed as ladies range time free.
It is a bit of a drive so I do not go as often as I like.
While the rubber is thinner it still increases the circumference a bit for my smaller hands.
It appears from the picture you posted the sleeve is over the the lower 1/2 of the safety and pushing it into the ‘firing’ position. It can not move outwards to the ‘safe’ position.
![Outerwear Sleeve Grey Jersey Personal protective equipment]()
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
1 - 20 of 43 Posts
