PistolGear "Slam Pads" for XD - Page 3 - XDTalk Forums - Your HS2000/SA-XD Information Source!

speeddeacon · 04-17-2008, 09:02 PM

Here's my first attempt at posting pictures. This is my IDPA gun with recently installed Pistolgear Operator Magwell and Canyon Creek extended mag release.

Let's see how it goes.

**Old School** · 04-18-2008, 07:34 AM

The pics look great!

OS

speeddeacon · 04-19-2008, 07:41 PM

Thanks. And thanks for the goods!

FarmerVincent · 04-28-2008, 06:52 AM

Old School,

I assume an XD9 Tactical with the Operator magwell and base pads still fits in the IDPA box? Perhaps an obvious question, but I wanted to ask it to make sure.

Thanks for all the XD goodies.

**Old School** · 04-28-2008, 07:06 AM

Quote:

Originally Posted by FarmerVincent

Old School,

I assume an XD9 Tactical with the Operator magwell and base pads still fits in the IDPA box? Perhaps an obvious question, but I wanted to ask it to make sure.

Thanks for all the XD goodies.

Yes. That is exactly my IDPA setup.

XDTac40 · 05-26-2008, 07:39 PM

Hey guys, just wanted to say I have ordered a few things from Pistolgear.com and they are awsome! Very fast shipping times and have great products. I could not wait for the operator to be in stock so I could take of the flimsy plastic magwell I had on there before and install a quality piece on my 5" tact .40. But after putting it on and installing the base pads on Fri afternoon I had a CCW match shoot on sunday. Well that went really bad! The mags would not drop out free but instead had to be pulled out and one was so hard to get out I ended up pulling the basepad off trying to get the clip out and had to lock back the slide and push it out from the top. Got home and noticed that the front part of the bottom plate on the clip was hitting the inside of the magwell and causing it to kind of wedge in as the clip locked into place. Well to fix this I used a dremmel and took some of the lip off of the clip until it would drop free. No big deal but just a heads up to pistol gear to maybe play around with this some, but it is a great part and now that I have that fixed I am back in business.

**Old School** · 05-26-2008, 08:38 PM

Quote:

Originally Posted by XDTac40

No big deal but just a heads up to pistol gear to maybe play around with this some, but it is a great part and now that I have that fixed I am back in business.

Thanks for the write up and sorry for the trouble. If you have a camera, can you email us a picture? I ask because we have not seen this before and want to understand what is binding and where. Are these the stock basepads or do you have a magazine extension on the mags?

OS

XDTac40 · 05-27-2008, 05:18 PM

Yes they are the stock basepads, and I will take some pics here in a sec and post them.

XDTac40 · 05-27-2008, 05:41 PM

It wont let me make attachments so I will just post a link to the pics:
CarSponsor.com - Member Photo
CarSponsor.com - Member Photo

You can see the rub mark on the front of the magwell where the clip was in a bind.

**Old School** · 05-27-2008, 06:04 PM

Quote:

Originally Posted by XDTac40

It wont let me make attachments so I will just post a link to the pics:
CarSponsor.com - Member Photo
CarSponsor.com - Member Photo

You can see the rub mark on the front of the magwell where the clip was in a bind.

Well that's your problem, right there! Your magwell is not tight enough against the frame. In the first pic there is a gap. There should be no gap. Loosen both screws and hit the magwell on the bottom until it fully seats on the frame. Again, there should be no gap on the sides and rear.

OS

04-17-2008, 09:02 PM	#21
speeddeacon XDTalk Member Join Date: Jun 2007 Posts: 47	Here's my first attempt at posting pictures. This is my IDPA gun with recently installed Pistolgear Operator Magwell and Canyon Creek extended mag release. Let's see how it goes. __________________ XD9 Tactical, Springer Precision Trigger Job, Dawson FO front/target rear, BarSto fitted barrel, DGR, Pistolgear Operator Magwell, Canyon Creek Extended mag release XD40 Tactical, Springer Precision Trigger job, Dawson FO front/target rear, BarSto fitted barrel, DGR XD357 Service, Tritium XD9SC the wife's personal gun

04-18-2008, 07:34 AM	#22
Old School XDTalk 5K Member Join Date: Dec 2003 Location: Illinois Posts: 7,522	The pics look great! OS __________________ Visit www.pistolgear.com for all of your XD needs!

04-19-2008, 07:41 PM	#23
speeddeacon XDTalk Member Join Date: Jun 2007 Posts: 47	Thanks. And thanks for the goods! __________________ XD9 Tactical, Springer Precision Trigger Job, Dawson FO front/target rear, BarSto fitted barrel, DGR, Pistolgear Operator Magwell, Canyon Creek Extended mag release XD40 Tactical, Springer Precision Trigger job, Dawson FO front/target rear, BarSto fitted barrel, DGR XD357 Service, Tritium XD9SC the wife's personal gun

05-26-2008, 07:39 PM	#26
XDTac40 XDTalk Newbie Join Date: Feb 2008 Posts: 5	Operator Magwell Jam Hey guys, just wanted to say I have ordered a few things from Pistolgear.com and they are awsome! Very fast shipping times and have great products. I could not wait for the operator to be in stock so I could take of the flimsy plastic magwell I had on there before and install a quality piece on my 5" tact .40. But after putting it on and installing the base pads on Fri afternoon I had a CCW match shoot on sunday. Well that went really bad! The mags would not drop out free but instead had to be pulled out and one was so hard to get out I ended up pulling the basepad off trying to get the clip out and had to lock back the slide and push it out from the top. Got home and noticed that the front part of the bottom plate on the clip was hitting the inside of the magwell and causing it to kind of wedge in as the clip locked into place. Well to fix this I used a dremmel and took some of the lip off of the clip until it would drop free. No big deal but just a heads up to pistol gear to maybe play around with this some, but it is a great part and now that I have that fixed I am back in business.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-28-2008, 06:52 AM	#24
FarmerVincent XDTalk Member Join Date: Nov 2007 Location: McKinney, TX Posts: 30	Old School, I assume an XD9 Tactical with the Operator magwell and base pads still fits in the IDPA box? Perhaps an obvious question, but I wanted to ask it to make sure. Thanks for all the XD goodies.

05-27-2008, 05:18 PM	#28
XDTac40 XDTalk Newbie Join Date: Feb 2008 Posts: 5	Yes they are the stock basepads, and I will take some pics here in a sec and post them.

05-27-2008, 05:41 PM	#29
XDTac40 XDTalk Newbie Join Date: Feb 2008 Posts: 5	It wont let me make attachments so I will just post a link to the pics: CarSponsor.com - Member Photo CarSponsor.com - Member Photo You can see the rub mark on the front of the magwell where the clip was in a bind.