|
|
11-01-2009, 06:06 PM
|
 #1
|
|
XDTalk 5K Member
 
Join Date: Feb 2007
Location: Detroit
Posts: 5,745
|
Reassembly dilemma
Do yall hate me yet?
 Lesson #1 I learned from this, don't try a complete dis/as of a 1911 without someone else to help you along around.ok anyways my pistol is in a million pieces so I need help. trying to follow this link Guerrilla Gunsmith --- 1911 Detailed Disassembly for re-assembly. I get it totally together or so it seems and can't pull the hammer back to allow the safety to be installed. I assume I'm putting one of the springs on the wrong side of something and I can't figure this out, tried it multiple ways so, Sear spring, which way is it supposed to be on the sear when installed? Pretty sure I'm putting it in the wrong place in relation to the sear. Oh trigger is frozen as well. when its like this Thanks guys. Tim
__________________
The three requirements for a school shooting. 1 know the floorplan. 2 Know the threats inside the location and response time/entry time for the police 3. Royally screwed up intelligent analytic mind. We need more laws to protect these three rights. Ban guns in schools, it obviously works. Last edited by yocan; 11-01-2009 at 06:11 PM. |
| Share | |
|
    
|
|
11-01-2009, 06:51 PM
|
#2 |
|
XDTalk 100 Member
Join Date: Dec 2006
Location: Kansas
Posts: 132
|
If everything is in correctly the left arm of the spring (the bent one) should rest on the sear, the middle leg on the disconnector, and the right arm is the one that powers the grip safety. With the spring installed, put the mainspring housing in far enough to capture the spring in the proper place. This will allow you to insert the grip safety & pin. Push the mainsring housing up & install it's pin, then the thumb safety can be installed. Once you have done it a few times, it is easy. Good Luck.
__________________
If the thunder don't get you, then the lightening will! |
| Share | |
|
|
|
|
11-01-2009, 07:54 PM
|
#5 |
|
XDTalk 500 Member
Join Date: Sep 2008
Location: Longview, TX
Posts: 656
|
__________________
Ya'll be careful out there...ETexPops XD9sc w/ TFO's XD45c w/ Trijicon Night Sights Browning Buckmark Camper w/Garret Red Dot Browning Buckmark Camper w/Fiber Optics Taurus PT1911-blue Kimber Stainless Ultra Carry w/ Meprolight Sights Ruger 10/22 Model 1219 w/ Busnell Banner 3x9 NEF Pardner Pump 18.5" w/ Truglo Fiber Optics Hi Point 995TS w/ Bushnell Red Dot S&W MOE M&P 15 Bunch of other long guns |
| Share | |
|
|
|
|
11-01-2009, 09:46 PM
|
#6 | |
|
XDTalk 5K Member
Join Date: Feb 2007
Location: Detroit
Posts: 5,745
|
Quote:
now I've dis/ased it over 70 times today my new pistol is not so anymore dang. Only love marks that showed up the main spring roll pin that corner left side is a smidgen shiny, and a mark from the pin on the safety on the grip safety. but the whole thing is loose now. dang.
__________________
The three requirements for a school shooting. 1 know the floorplan. 2 Know the threats inside the location and response time/entry time for the police 3. Royally screwed up intelligent analytic mind. We need more laws to protect these three rights. Ban guns in schools, it obviously works. |
|
| Share | ||
|
|
|
 |
| Thread Tools | |
| Display Modes | |
|
|
LinkBacks (?)
LinkBack to this Thread: http://www.xdtalk.com/forums/m1911/134695-reassembly-dilemma.html
|
||||
| Posted By | For | Type | Date | |
| XDTalk Forums - Your HS2000/SA-XD Information Source! | This thread | Refback | 11-01-2009 06:51 PM | |
Linear Mode
