Mag Loader - Page 2 - XDTalk Forums - Your HS2000/SA-XD Information Source!

dbrownusarmy · 01-22-2005, 05:45 PM

Quote:

Originally Posted by blaib

What model of the HKS speed loaders do you guy's use? I dont see one listed for the XD40. Thanks I really need one these new hi cap mags are almost impossible to load.
Brian

This is the one that I just picked up. I got mine at the range for 13. But you can get one on pistol-gear.com for 9.95, so this is a great deal, and Scott is the faster shipper that I have dealt with.
I Highly recommend this if you are going to be shooting a good deal.
HKS Speed Loader at Pistol-Gear

Hope that helps.

Dave

Paladin · 01-22-2005, 08:06 PM

Yes, that's the one I bougth too. Pistol Gear had it to me within a few days after I ordered it. Great folks and fine service.

jcaniz · 02-02-2005, 03:54 PM

pistol gear does have super fast shipping.
Highly recommend.

**The Grand Pooh-Bah** · 02-02-2005, 06:58 PM

Quote:

Originally Posted by one-eyed-fatman

They don't make them for the sub. I modified mine to work.

Tell me more....how did you get it to work? What mods....pictures help.

WyoBob · 02-02-2005, 07:21 PM

Quote:

Originally Posted by The Grand Pooh-Bah

Quote:

Originally Posted by one-eyed-fatman

They don't make them for the sub. I modified mine to work.

Tell me more....how did you get it to work? What mods....pictures help.

For my XD40 SC short mags, I used a dremel tool with a cylindrical bit (like an end mill) and ground a new slot for the shorter mag. For the one mag with the Pierce extension, I just ground a contour to accomodate. A milling machine would be ideal for those with less than steady hands but the hand-held Dremel mod works.

WyoBob

one-eyed-fatman · 02-02-2005, 07:42 PM

Basically what I did was cut a piece of alumium down to about 1/4 X 1/4 X say one inch in length. I angled the metal top and bottom to fit the mag and the bottom of the speedloader then drilled a hole and bolted it into place. I'll take a picture tomorrow and show it. The mag slips in on top of the metal and holds the mag in place.

jgdean85 · 02-02-2005, 08:32 PM

Quote:

Originally Posted by phil evans

hks loaders will not work with pearce extender grips.
i use adco super thumb.

Which one? The ST2 for glock?

pmfinnegan2 · 02-03-2005, 07:42 AM

would love to see pics and know what model number HKS speedloader you used.

one-eyed-fatman · 02-03-2005, 09:36 AM

Here's a pic of my 941 with the block installed at the bottom of the speedloader. If it's not a good enough pic let me know and I will try to put up a better one.

InspectorNugger · 02-03-2005, 01:14 PM

I agree...the #941 is the model number you want for the XD mags. I too had to do a little slot milling with my Dremel to allow the bottom "foot" of the mags to fully seat in the loader. Works like a charm...got mine from Pistol Gear.

01-22-2005, 08:06 PM	#12
Paladin XDTalk 100 Member Join Date: Dec 2004 Location: Northcentral Florida Posts: 286	Yes, that's the one I bougth too. Pistol Gear had it to me within a few days after I ordered it. Great folks and fine service. __________________ XD-9 Bi-Tone Service (Home Defense) XD-9 Tactical (USPSA Production Competition) Black Stainless Loaded 1911-A1 (USPSA L-10 Competition) Brazos Pro SC .38 Super (USPSA Open Competition)

02-02-2005, 03:54 PM	#13
jcaniz XDTalk Newbie Join Date: Jan 2005 Location: Miami Fla Posts: 26	pistol gear does have super fast shipping. Highly recommend. __________________ xd 40 sig 229 sig 239 g21/30 sa 1911 hi cap kel tec 32 beretta 92f bushmaster ar 15 ak-47 cx4 storm kel tec 2000

02-02-2005, 07:42 PM	#16
one-eyed-fatman XDTalk 10K Member Join Date: Mar 2004 Posts: 10,221	Basically what I did was cut a piece of alumium down to about 1/4 X 1/4 X say one inch in length. I angled the metal top and bottom to fit the mag and the bottom of the speedloader then drilled a hole and bolted it into place. I'll take a picture tomorrow and show it. The mag slips in on top of the metal and holds the mag in place. __________________ http://home.houston.rr.com/gunpics/images/one%20eye.wav

02-03-2005, 09:36 AM	#19
one-eyed-fatman XDTalk 10K Member Join Date: Mar 2004 Posts: 10,221	Here's a pic of my 941 with the block installed at the bottom of the speedloader. If it's not a good enough pic let me know and I will try to put up a better one. __________________ http://home.houston.rr.com/gunpics/images/one%20eye.wav

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-03-2005, 07:42 AM	#18
pmfinnegan2 XDTalk Member Join Date: Jan 2005 Location: S.E. Michigan Posts: 42	would love to see pics and know what model number HKS speedloader you used.

02-03-2005, 01:14 PM	#20
InspectorNugger XDTalk 100 Member Join Date: Nov 2004 Location: Idaho Falls, ID Posts: 223	I agree...the #941 is the model number you want for the XD mags. I too had to do a little slot milling with my Dremel to allow the bottom "foot" of the mags to fully seat in the loader. Works like a charm...got mine from Pistol Gear.