Follow up to trigger work

[agalindo]

I learned by taking my gun apart. Ajamesp51 disassembly web page, mike+p+ and ichy_trigger's posts, other posts. Also from just viewing at the manual and parts list. Just sat around one week end took the slide off and pulled the trigger and watched what happened. Also do a search on glock .25 trigger job.

http://www.hs2000talk.com/viewtopic....=trigger+reset

http://www.hs2000talk.com/viewtopic....ght=overtravel

[agalindo]

Holy crap is that a hole in your frame? Shocked

Yea some one on this site posted a pic with screw in the frame so I tried it out.

Ichy_trigger where did you find a screw for your overtravel?

[agalindo]

This Htown's XD with some of the mods.

Overtravel, and reset saftey lever and trigger bar.




slide fireing pin and trigger saftey.



Video

[pla]

Has anyone posted a breakdown of what S.A. or C.C. does as part of their jobs?

As for a screw... how about a small metal insert threaded on the inside. Drill your hole, put a drop of epoxy in the hole, insert the insert , screw in a set screw with a little blue locktite...

They use inserts like this in laptops... you could also buy a piercing jewelry type barbell and cut it in half...


...Just thinking out loud...


-Liam

[agalindo]

http://www.hs2000talk.com/viewtopic....+creek+trigger

[ichy_trigger]

Originally Posted by agalindo

Yea some one on this site posted a pic with screw in the frame so I tried it out.

Ichy_trigger where did you find a screw for your overtravel?

At the screw store...DUH!!! I got it at Lowes or ACE Hardware, I think I have an extra one around here in the tool box. What tap did you use? I THINK I used a 4-40. I will run out to the garage and check if you want and if you used the same size, I THINK I have a spare screw around here that I can send you. I bought 3 different lengths to try. You can just grind it down to the proper length that you need or I can run out and pick one up for you. Let me know....

[agalindo]

You know I'm not sure what size the tap was I'll have to check. I'm going to Home Depot sometime this week so I'll just check there for a screw, thanks for the offer though.

[ichy_trigger]

Originally Posted by agalindo

You know I'm not sure what size the tap was I'll have to check. I'm going to Home Depot sometime this week so I'll just check there for a screw, thanks for the offer though.

Let me know, I KNOW I can get one here, we have an ACE hardware that has **** in stock that NO ONE else has. If I have what you need in my box, its yours.

[mike+p+]

As for a screw... how about a small metal insert threaded on the inside. Drill your hole, put a drop of epoxy in the hole, insert the insert , screw in a set screw with a little blue locktite...

That's not a bad idea. I just did some grinding on the screw head to fine tune it's height.

Cap'n Larry's helpful hint:
Take the slide off (after triple checking to make sure it's unloaded of course). Then push down on the trigger bar to reset the trigger. Then pull the trigger while watching the safety lever move up. The safety lever height should be set at the point when all the trigger take up has been used, just before there is any tension. If the height is set any more than this ...then the sear is starting to be engaged. Don't let that happen. Note: I don't have an XD in my hands, I'm going from memory.

[agalindo]

Let me know, I KNOW I can get one here, we have an ACE hardware that has **** in stock that NO ONE else has. If I have what you need in my box, its yours.

Th anks Ichy_trigger I'll PM if I'm not able to find one.

Does anybody have different way to get rid of the pretravel? Any Ideas. I guess I could also use a screw then I could be adjustable.